Questions & Answers - Questions récentes tagguées red-yellow-flash

EVO-ALL Red and yellow balloon flashes

Sat, 12 Sep 2026 17:32:26 +0000

I have a problem related to programming on a 2023 Audi car, and at the beginning there was no problem, when I checked an update, and when I sent it to the vehicle, it did not work remotely, otherwise it appeared to me in red and yellow colors in a device, and when I searched for it, it said that it is not possible to connect, and until the factory has been reset, and also on its programming, it shows me the colors red and yellow, and when I connected the device to a computer, he said it is not possible to see.I have a problem related to programming on a 2023 Audi car, and at the beginning there was no problem, when I checked an update and when I sent it to the vehicle, it did not work remotely, otherwise it appeared to me in red and yellow colors in a device, and when I searched for it, it was not possible to connect, and until the factory was reset and also on its programming, the colors red and yellow appear to me, and when I connected the device to a computer, he said it could not take the programming and follow.I have a problem related to programming on a 2023 Audi car and it was initially no problem when I check for an update and when I sent it to the vehicle it does not work remotely otherwise it appears to me in red and yellow colors in a device and when I look for it that it is not possible to connect and until the factory has been reset and also on its programming it shows me the two colors red and yellow and when I connected the device to the computer he said it cannot take the programming and follow the number 1 of the steps and when I follow the steps the same problem returns in the red and yellow colors I think it needs to reset the factory through youI have a problem related to programming on a 2023 Audi car, and at the beginning there was no problem, when I checked an update, and when I sent it to the vehicle, it did not work remotely, otherwise it appeared to me in red and yellow colors in a device, and when I searched for it, it was not possible to connect, and until the factory was reset and also on its programming, it shows me the colors red and yellow, and when I connected the device to a computer, he said it could not take the programming, and I followed the number 1 of the steps, and when I follow the steps, the same problem returns in the colors red and yellow, I think it needs to be reset the factory throughI have a problem related to programming on a 2023 Audi car and it was initially no problem when I check for an update and when I sent it to the vehicle it does not work remotely otherwise it appears to me in red and yellow colors in a device and when I look for it that it is not possible to connect and until the factory has been reset and also on its programming it shows me the two colors red and yellow and when I connected the device to the computer he said it cannot take the programming and follow the number 1 of the steps and when I follow the steps the same problem returns in the red and yellow colors I think it needs to reset the factory through you
SN: 001A07 595395

My remote start isn't working it's flashing red and yellow

Mon, 11 Aug 2025 15:06:03 +0000

Tried my remote start and wouldn't work looked at the module and it's flashing yellow and red. To also state this was in the truck when I purchased it so I have no literature or anything on this. Any help would be appreciated. Evo one SN: 002B04 071021

2014 Audi Q5 Evo All not flashing yellow in step 8 of Key bypass programming

Thu, 14 Nov 2024 14:01:54 +0000

Im not able to proceed from step 7 in guide 77151. When it should begin to flash yellow and red alternating it just flashes red.

EVO ALL Stuck in Yellow and Red Light Flashing

Sun, 27 Oct 2024 00:34:31 +0000

Hello,

I am installing this on my 2012 VW Tiguan. I followed the process guide 92511. After decryptor and returning the vehicle, yellow and red LEDs flash, instead of staying on like explained on Step 13.

Now it says my unit (SN 001A07 559614) has recheaed its limit and I am really stuck.

Can you please assist?

Thanks,

Andrew

lexus gs450h L10 fsport 2012 PUSH TO START EVO-ALL does flash red and yellow.

Fri, 09 Dec 2022 14:08:03 +0000

Can someone help, when I connect EVO-ALL to car and follow instruction, it starts flashing red and yellow. According to instruction I have to dcrypt module, but when I try to do it, program says invalid key data. master restart didn't help.

SN #001A07 391294

red flashing instead of red and yellow flashing?

Sun, 10 Jan 2021 06:06:33 +0000

Mazda cx-5 2018

Evo all guide # 66311

on step 13 I have an only red light flashing once every second and did not stop!!

I tried and read different solution founded here, but it ends with the same red flashing

all wires connected correctly

2018 Mazda 3 Automatic - Ignition comes ON but does not flash Yellow and Red (Step 13)

Sun, 03 Jan 2021 16:05:42 +0000

Hi Fortin Q/A forum. Installing a EVO-MAZT1 which I first connected to Fortin FlashLink Manager to upload the latest firmware (suggested 85.10) on Hardware 7.0. Loaded Suggested Options, then went to the car to perform Programming. Programming Steps 1-12 go as planned, but when the ignition turns ON and OFF by the module, the Yellow and Red LEDs do not flash as indicated in the guide. I disconnected the module as indicated by the instruction manual (disconnect all connectors, saving the 4-Pin Data connector for last) and then connected it back up to FlashLink Manager to run DCryptor.

DCryptor says INVALID KEY DATA and "The immobilizer data received by the bypass module is incomplete. Please try again. If this error persists reconnect the module to the vehicle and start programming procedure from STEP 1."

Via the troubleshooting guides, I removed the batteries from the key fobs and tried again. Verified connection to the data key wire was correct (Car's Red wire to bypass' Light Blue and Black wire) and secure (shaved insulation, wire inserted through conductors, wire wrapped, soldered, and taped). Door lock actions can be seen on the bypass/remote start module as indicated by the Blue LED. I'm confident those wires are connected correctly and securly as well.

I tried all of the above with and without the front fuse box ground to Pin 11. Someone please explain what that does, but the manual did not indicate if it was mandatory or optional so I tried both ways.

In the end, I can't get DCryptor to program the module with the learning received during programming. I fear it has to do with the Yellow and Red LEDs not flashing. Help would be appreciated. Thanks!

2020 F150 auto start not working, lights just blink alternating yellow and red.

Tue, 28 Jul 2020 16:19:31 +0000

I have a 2020 Ford F150 std-key-with-keyless and cant get the auto start to work. I set the evo-all to blue for programming, then I plug in the bottom cable. Turn key to on, yelow red leds turn on then start to blink and alternate. After 20 seconds I turn key to off and disconnect it. i then take it to my laptop and program and flash it. Once thats done I connect it per the instructions but the problem is I never get the red yellow lights to go solid. They just keep alternating and blinking. Turning the key on nothing change or off all I get is red and yellow blinking lights.

Heres a video I did of my issue. I set the start time to the issue mark but you can scan it all if needed.
https://youtu.be/eNiUY9VVx-c?t=363

Thanks

FAQ: GM Flashing RED and YELLOW

Wed, 15 Jul 2020 17:58:11 +0000

If the RED and YELLOW flash during programming after cyling the key to the ON position, do this.

Turn car off
Plug in ONLY the RED connector in the EVO
Start car and let run 5 secs.
Shut down car.
Do NOT disconnect RED connector
Wait 20-30 Seconds
Start programming