Questions & Answers - Questions récentes tagguées push-to-start

Highlander

Wed, 21 Oct 2026 18:59:45 +0000

Two months ago, I installed an Evo-ALL module in a 2019 Highlander. The programming process proved difficult—the system only worked on the third attempt. The new module didn't work, so I used an old one instead.

The client called to say that the Fortin device has stopped working.

Is it possible that the vehicle has a factory-installed remote start system that is causing interference? Where should I look for it?

2017 Audi A6 2.0 TDI EVO-ONE: no crank unless brake pressed (guide 79791)

Mon, 19 Oct 2026 13:48:28 +0000

Hello Fortin Support,

I need help verifying the brake activation and CAN1 wiring for an EVO-ONE installed in a 2017 Audi A6 C7.5 2.0 TDI, right-hand drive, automatic, push-to-start.

Installation guide: #79791

Bypass firmware: 60.12

Remote starter firmware: 1.31

DCryptor completed successfully.

Symptoms:

- Pressing lock three times on the OEM remote triggers the ignition, but the engine will not crank unless I physically press the brake pedal.

- The brake lights do not illuminate during the remote-start sequence when the pedal is not pressed.

- If I hold the brake pedal, the engine starts but shuts off after approximately 2 seconds.

Current connections:

- EVO-ONE D2 Yellow/Blue is connected to the vehicle Red/Black brake circuit.

- CAN1 is tapped into the Orange/Green and Orange/Brown twisted pair at the brown 16-pin BCM connector C. The Fortin guide shows a black connector, so I would like to confirm whether my connection point is correct for this RHD C7.5 vehicle.

Could you please verify:

1. The correct brake activation signal for this exact vehicle: connector and pin, wire colour, required polarity/voltage, and whether D2 Yellow/Blue should connect directly to the Red/Black circuit or requires a different interface. Is this the correct signal to satisfy the push-to-start brake requirement?

2. The correct CAN1 High/Low connection point, connector and pin numbers for the RHD C7.5, including whether the brown 16-pin BCM C Orange/Green and Orange/Brown pair is correct despite the black connector shown in guide #79791.

3. The recommended fix and any required firmware or option changes for the no-crank condition and 2-second shutdown.

Thank you.

2014 Tiguan Firmware per the guide is not found.....

Sun, 18 Oct 2026 18:02:06 +0000

I'm about to install remote start in my 2014 VW Tiguan push start but the guide lists a firmware version of 75.38 but the Flashlink Manager only lists 3 options for fimrware updates for my evo-all, 4.20 Beta, 0.99 Beta, and 0.90 Beta. Which of these three should I install to make sure there are no firmware related issues since none are similar to the firmware version listed in the installation guide (Guide 62501) documentation? Thanks!!!!

The coolant does not heat up during remote starting.

Sun, 11 Oct 2026 16:21:03 +0000

Hello. I installed an Evo-One on a 2014 Vezel (selecting the 2016 HR-V setting). It was a hybrid vehicle. I selected option D4 in the settings. Do I also need to enable option "26-2" under the "remote start" settings? The client called to say that the engine coolant doesn't heat up during remote start, and when he drives off after remote starting, the blue "cold engine" light remains on. Why do we cut the IGN2 wire?

AutoStart is not working for Honda CRV 2015 Touring - Push to Start

Sat, 10 Oct 2026 20:16:06 +0000

I installed a Fortin EVO-ONE with the THAR-HON3 T-harness on a 2015 Honda CR-V Touring Model Push-to-Start .
The module programs correctly, Dcryptor completed successfully, and CAN functions work (lock/unlock, ignition status).
However, the EVO-ONE never outputs ignition during remote start.

Did Enabled option D2

Programmed Remote Started option Function 2 Mode 2

Programmed Remote Started option for R S OEM Remote Stand alone

Function 38 Mode 2

Getting Error while Decrypt Process - Decrpypt Limit has been reached for this Car.

Model - EVO-ONE

Date : 07/2025

SN : 002B04 734872

Appreciate your help to solve the issue please.

Thanks

2018 CRETA

Mon, 28 Sep 2026 12:46:54 +0000

I installed the Evo-One on a 2018 Hyundai Creta (selecting the Kona model). It works well, but where can I find the wire for the "Take Over" function, so the engine doesn't shut off?

Ioniq 2021

Sun, 20 Sep 2026 14:03:17 +0000

Hello. The 2021 Ioniq manual states the following... "US Models: If the (~) PATS Data wire is not present, the vehicle is not equipped with an immobilizer. For CAN functions, use programming #2." But where is this "programming #2"?

Compatibility confirmation Fortin EVO-ONE-441 – Mazda CX-5 2017

Wed, 16 Sep 2026 11:03:57 +0000

Hello,
I have a 2017 Mazda CX-5 2.5 Grand Touring, USA specification, Push-to-Start, automatic transmission.
VIN: JM3KFBDLXH0170683

I would like to install Fortin EVO-ONE-441 with the appropriate Mazda T-harness.
Please confirm that this setup is fully compatible with my vehicle and tell me exactly which T-harness and firmware/installation guide are required.
I would also like the system to work with the included remote controls.

Thank you.

2019 Jeep Cherokee EVO-ALL won’t start

Fri, 11 Sep 2026 18:59:57 +0000

I need help. I've been a couple days now with this. EVO-ALL installed programming goes fine, but it will not tun over the car. Module comes to life on 3x lock, cycles the gauges, but then just stops and tries again.

2019 Jeep Cherokee PTS not starting on EVO-CHRT7

Fri, 11 Sep 2026 15:44:19 +0000

What do i need for remote start of a 2012 hyundai genesis sedan 3.8 with push start?

Thu, 27 Aug 2026 18:45:15 +0000

Hi whay would i need for remote start for a 2012 hyundai genesis sedan 3.8 push start? Would it be plug and play?

Thank you

2023 Toyota Tacoma pts stuck at last step (Dcryptor)

Wed, 05 Aug 2026 00:41:48 +0000

I install Evo One, Thar-Toy6 harness, and 942 rf kit. Flash for remote start and alarm, siren (a7), shock sensor, long tone, 60 sec, and hood pin off (A11). I'm stuck at the last step Dcryptor, now saying Dcryptor limit has been reached for this car. I'm sure flash also has been reached from flashing many times along with programing step 1-5 hoping it will work lol. Please help.

module info: 11/24, Bypass sn:002B04703522 and Remote starter sn: 002B07703522 (Idk which is the sn)

Thank Al

Will I need to reconfigure EVO-ONE if adding RFK442

Thu, 30 Jul 2026 17:14:48 +0000

Hi I installed a evo one in my 2021 Mazda CX5 and now want to install the RFK442 fobs. Will that require me to reconfigure the evo one?

Why is the vehicle not responding?

Sat, 18 Jul 2026 14:20:58 +0000

I have a Fortin evo all, a evo start lte, and also shock sensor. I’m getting feedback from the car which shows up on the Evo start, but commands sent aren’t working, and when the evo alarm goes off the vehicle alarm does not. I was hoping you could tell me if there’s some wiring that I’m not aware of, or if the process with the dcryptor is wrong? everything seemed to program correctly. I used the CHR7 T-harness and it’s on a 2018 grand Cherokee. What am I missing?

Q50 not remote starting

Mon, 06 Jul 2026 04:12:34 +0000

i have a 2015 infiniti Q50

SN-002B04 759527

i installed the evo-one with thar-nis4 t harness and RF942 kit.

programmed, decrypted and reinstalled tested with oem keyfob worked great, than i programmed the 2 RF remotes, test again worked good 3 times then just stopped working. i can still unlock/lock with all 3 fobs. it will try to remote start, gets to where it should crank and nothing.

MG6 2020 (SAIC Motors)

Sat, 13 Jun 2026 18:42:17 +0000

Hello,

I have MG6 2nd Generation model year 2020 (chinese made by SAIC Morors) push to start, I want to have a standalone remote starter similar to evo all and evo one in some vehicles ( i did install them in my previous car Nissan Qashqai ) and recently in my brother's car VW Tiguan.

I am desperate for an engine remote start solution specially by fortin as we live in hot climate regions and precooling the cabin with A/C is kinda of a must

2017 Renegade

Fri, 12 Jun 2026 21:22:01 +0000

Hello. When I'm programming the Evo-All on a 2017 Jeep Renegade, the blue LED starts blinking after 5 seconds (after pressing the button), and after turning off the ignition, the red LED stays on continuously. I've already tried it on two modules.

EVO-ALL cannot program sacrificied key in a standlone installation for Tiguan 2020 PTS

Thu, 11 Jun 2026 15:08:31 +0000

I am trying to setup a standalone installation for Volkswagen Tiguan 2020 European Trim with PTS and with digital cluster
I have wrapped the sacrificied key (even tried an oem ring) and connected the wiring following the guide # 94761

The ignition is not turning ON during programming (seems that Evo-All is not getting the key data from pin D5 and hence not sending it via pin D4 to the vehicle)
Hence when i press ingition ON during progamming the car tells me to get the key inside the vehicle

Evo-All SN: 001A07 026604
Date: 05/2019
Evo-All FW: 61.35

Sacrificed Key
Sacrificed Key_2
OEM Transponder Antenna Connection
OEM Transponder Antenna Socket Front View

Need to get installation guide

Thu, 28 May 2026 08:44:07 +0000

Need to get installation guide for Evo all in one device , my car is nissan xtrail t32, 2018 (Rogue). Push to start

2017 IS-300

Mon, 25 May 2026 14:08:46 +0000

Hello. I installed a remote starter on a 2017 IS-300. I reprogrammed the firmware three times, but it didn't help. It programmed successfully, but when I pressed the button on the factory remote, the blue LED didn't respond (001A07213969). After that, I installed a different module, and it worked. What could be the cause?

I’m looking for a t harness for a 2019 Subaru brz push start

Mon, 11 May 2026 14:00:01 +0000

T harness for Subaru brz

Does your can bus interface work with a 2005 Pontiac gto

Thu, 07 May 2026 03:04:59 +0000

Can ANY of your devices (immobilizers) work on a 2005 Pontiac gto?

What’s the range of the phone application

Fri, 27 Mar 2026 10:56:54 +0000

If i install the EVO application i want to know what’s the range that i can start my Prado from the phone app? I work in an office tower on the 23 floor and my car is parked on the ground floor so i wanted to know if it will detect this range

2007 rav4 (PTS) and Evo-Key

Tue, 24 Mar 2026 21:07:01 +0000

I installed Evo-Key via IMO-IMI with Avital Remote Start...Even the take-over worked too.

Firmware for 2010 Rav4

Tue, 17 Mar 2026 00:21:45 +0000

Can you help me flash older firmware on my Evo-All? For example, from 79/56 to 79/65 ? S/N 001A08005655

EVO-ALL RF64 -2 Remote, antana LED wont go on? WHY?

Mon, 09 Feb 2026 05:25:20 +0000

Hi again! 2019 Toyota Highlander Push-start.

So Ive been able to go through GUIDE # 70751, and everything works great. The Blue LED is on, flashes, and turns off. I go to page 7 because the remotes I have are the RF64-2W ( is this what I am supposed to do?), but step 3, when it says that the "antenna LEDs should turn on, then blink as you press the brake, turning all three LEDs on the module on." This does not occur; the module stays Yellow and the antenna doesn't turn on once the ignition is on 2X press.

What am I doing wrong? Do I go straight to the remote GUIDE # 33021? When the car is on, the remote works. Is there a step-by-step video or something? I feel like I am just missing one part.

Need help q50 not starting

Sun, 08 Feb 2026 08:13:09 +0000

I have Infiniti q50 2016 3.0L

I installed the EVO-NIST4 to use with OEM key fob , the ignition is tuning on but no cranking, then the red LED flashes 3 times,

the SN is 001A07471366

here is the sequences of LEDs during the attempt

OEM key fob locks 3 times

red LED

red and yellow LED

Then yellow LED is on

vehicle hazards indicator flashed 7 time

After that the red LED flashed 3 time

I checked all the connectors

The car locks and unlocks when the blue LED flashes

I didn’t connect the hood pin

I reprogramed the module

followed the recommended option by the software but I’m not sure the options I’m selecting are correct for my setup

I’m following guide 75841

No start Q50 2016 EVO-NIST4

Wed, 04 Feb 2026 08:38:27 +0000

Hi,

I have Infiniti q50 2016 3.0L

I installed the EVO-NIST4 to use with OEM key fob , the ignition is tuning on but no cranking, then the red LED flashes 3 times,

the SN is 001A07471366

here is the sequences of LEDs during the attempt

OEM key fob locks 3 times

red

red and yellow

yellow

vehicle hazards indicator flashed 7 time

red flashed 3 time

I checked all the connectors

The car locks and unlocks when the blue LED flashes

I didn’t connect the hood pin

reprogramed the module

followed the recommended option by the software but I’m not sure the options I’m selecting are correct for my setup

I’m following guide 75841

Any help would be appreciated

Porsche Macan compatibility availability ...

Fri, 30 Jan 2026 18:57:22 +0000

The Audi Q5 and the Porsche Macan share the same platform and both are produced under the Volkswagen Group. They not only share same engine on the base model ... they share similar electronics. The Fortin remote starter is available for the Q5, but not for the Macan. Any chance you will develop one for the Macan series?

Thank you ...

2016 KIA K7

Tue, 20 Jan 2026 11:53:26 +0000

Hello. I installed Evo-One on 2016 Kia K7 (on liquid gas...with start-stop).. I specified 2017 Kia Optima in the manager. The EMS wire was behind the passenger kick panel in the red connector on the bottom, second from the right. Behind the fuse, the ignition wire (ON) was pink...the ACC wire was white...the starter wire was yellow with a black stripe. The CAN wires were also located behind the fuses in a small connector... yellow and black... blue and orange. Everything worked well, but after opening the door, when I pressed the brake, the car stopped... When I pressed the start-stop button, the radio turned on, and the start-stop button also showed a yellow LED, but the car stopped when I pressed the brake.

I didn't use the ACC-2. It was blue, behind the fuses. The customer left satisfied, but I'm wondering what else can be added to prevent the car from stalling when the brake is applied?

If you could please send me the serial number of this Evo-One...I usually write down the numbers in a journal and now I forgot to write them down...

Kia K7 Cadenza

Mon, 19 Jan 2026 15:17:41 +0000

Hello. Does the remote start with three locks (38.2) work on 2015 Cadenza? ( with Evo-One)...I want to install it on K7

Dcryptor option greyed out.

Mon, 19 Jan 2026 01:18:55 +0000

Hello, I have a EVO-ONE-441 and a THAR-MAZ3 t-harness for my Mazda CX5 2021 Signature. When I get to the part where I press the push to start twice without the brake pressed and try to get the ignition sequence it flashes the correct colors. However when I reconnect the module back to the updater the dcrypt option is still greyed out.

2024 Hyundai Elantra N Fortin Evo One LTE Flashes red light 4 times after failed remote start.

Mon, 19 Jan 2026 00:16:32 +0000

All wires seems to be correct from the install manual. Can is reading correct. The car will crank when remote started but nothing. I don't see any security lights on the dash when I attempt to remote start. the red light will flash about 4 times on a failed start. from my understanding its possbily not reading the tach? is theres a recommended setting im missing in pro/wizard? theres no decryption required for the Hyundai correct? and i just program the key on "red" press button 6 times press ignition 2x wait for flashing blue and turn ignition off. I have a 6MT I have updated everything to the most recent firmware. i just cannot seem to figure out the last part. I also have the car under Tech Data-Link. do i have to learn the idle of the car at all for it to stay running? my blue light on the evo one lte dosn't light up when holding brake and holding button to learn tach. Any advice would be great! Thank you!

2011 Toyota RAV4 Push Start – Remote Start shuts off first time, runs fine second time

Mon, 12 Jan 2026 11:13:29 +0000

Hi everyone,

I installed a remote starter on a 2011 Toyota RAV4 push start using a Compustar 930S with CM900 brain and Fortin EVO-ALL bypass module.

On the first remote start attempt, the vehicle starts normally, then shuts off after about 5–6 seconds. Immediately after shutting down, the system automatically attempts to start the vehicle again without me pressing the remote, and on this second attempt it stays running normally.

Installation and programming were completed as instructed. No fault lights, and the EVO-ALL appears to be learned properly.

Has anyone seen this behavior before on Toyota push-to-start vehicles?

2016 WRX PTS start up and shutdown right away.

Sun, 28 Dec 2025 03:51:05 +0000

2016 Subaru WRX PTS start up and shutdown right away.

Tach Supersivion 20.6

2018 outback

Tue, 23 Dec 2025 16:19:37 +0000

I installed an Evo-One on 2018 Outback (PTS... 3-locked 002B04112054). Sometimes the car doesn't start on the first try and then starts on the second try... What could cause this? If the starter contact in the connector is faulty, then on the second attempt it closes, or what?

Ford remote start

Thu, 11 Dec 2025 06:08:07 +0000

Is it possible to install an Evo-All on a Ford like on a VW and a Juke?...With brakes and start-stop?

2018 Fusion

Wed, 10 Dec 2025 14:58:16 +0000

I installed Evo-All on 2018 Fusion. The car starts, but the interior heater doesn't turn on. Is this how it's supposed to be?

kia seltos

Sun, 07 Dec 2025 23:02:22 +0000

Hello. I installed an Evo-Key on 2020 (2021) Kia Seltos (I had two of them). During programming, after opening the ignition, both modules showed both red and yellow lights. Then I pressed the programming button seven times... (The red light flashed six times). I opened the ignition, and everything was fine. Why does the manual say six times?

KIA SELTOS

Tue, 02 Dec 2025 15:36:41 +0000

Hello. Which manual is suitable for remote start on a 2020 Kia Seltos?

T-harness availability for 2017 Forester XT PTS

Thu, 20 Nov 2025 03:23:53 +0000

Is there a T-Harness for a 2017 Forester XT push to start?

Description for THAR-ONE-SUB2 describes 2013+ support, but the details only list starting 2017 Impreza PTS as the earliest. Is there a page I'm missing?

anyone experience 2016 Mazda 6 steering issue after evo-one & T Harness install?

Fri, 14 Nov 2025 21:10:52 +0000

After installing evo-one with Thar-one-maz3 on a 2016 Mazda 6, I am experiencing intermittent steering wheel turning resistance, usually on right hand turns at slow speeds, issue goes away after restarting vehicle then eventually comes back.

Issue goes away completely after removing harness/device. I have tried 2 different T harnesses & Fortin modules, same issue.

I have a 2014 Mazda 3 with same Fortin Evo-one-Maz3 setup and I have 0 issues.

would appreciate some help figuring this out.

Volkswagen Golf 2017 Push-to-Start -Digital Dash

Wed, 12 Nov 2025 18:29:19 +0000

I have the EVO-VWT1 system installed in my VW Golf no key sacrifice. I am wanting to upgrade the dash from analog to digital. What changes if any do I need to make to my current system to keep the same functionality

Evo One randomly stopped starting the vehicle and I don't know why

Mon, 10 Nov 2025 14:47:48 +0000

I have been using my Evo One in my Mitsubishi Outland push-to-start for almost 2 years with no problems. Now, the last couple of weeks, it won't start the car. I click the OEM fob lock 3 times, the outside lights all light up like it is going to start. Even the dashboard lights all light up like it is going to start and the radio comes up, but nothing. After a few seconds everything goes back to being dark. I can still jump in the car and start it manually just fine. Any thoughts on where to start troubleshooting this?

What is the complete list of parts needed to install a remote engine start?

Thu, 23 Oct 2025 16:22:42 +0000

Hello

Please write a complete list of what is needed for self-connection, programming and setting up remote engine start from OEM key fob using Evo-All VWT1 unit on AUDI S3 8V 2015 with start button?

I can't understand whether I need only R-link or only TB-VW or do I need both of these units, and what is needed to program the immobilizer bypass so as not to leave the key in the car?

And do I need a transponder?

So that I can order everything at once and not have to order the missing parts to Ukraine again and only then figure out how to install it using the instructions :)

Що потрібно для встановлення Evo-All vwt1?

Tue, 21 Oct 2025 12:59:40 +0000

Hello, tell me, do I need any of these products R-LINK, FLASHLINK MOBILE, FLASHLINK UPDATER, TB-VW to install Evo-All vwt1 on Audi S3 8V 2015 so that remote engine start from the native key works? Do I need to flash the already installed Evo-All unit, or can I just buy the Fortin Evo-All VWT1 unit, install it on the car and everything will work right away? Please tell me what is needed to install remote engine start from the native key so that I can buy it all right away? because I will have friends who will send orders to Ukraine :)

I have a 2021 kia k5 and on one of the guides it says to cut the wire. Am i not connecting it to the EMS Comm wire

Mon, 20 Oct 2025 14:22:48 +0000

Am i not connecting the green wire to to the white EMS comm wire? Is it going to ground?

I need the full installation/programming guide for a remote start system for a push to start 2014 Mitsubishi Outlander

Sun, 05 Oct 2025 18:47:20 +0000

I purchased a remote start system for a push to start 2014 Mitsubishi Outlander last year and didn't get around to installing it. I am now ready to install it, but do not have the full installation/programming guide for the remote start system.

Can you please send me the full installation/programming guide for the remote start system so I am able to proceed? Thank you!

2020 Honda Civic Starts But No Power to Head Unit and SRS Airbag Error

Wed, 01 Oct 2025 19:52:29 +0000

Installed an Evo-One with Evo-Start on a manual transmission 2020 Civic Sport. Can start the car just fine with the OEM remote or the app but when using either there is no power to the head unit and there is also an SRS airbag alert. This all resets after restarting the car but I am wondering how to keep this from happening. After doing some research i believe ignition 2 powers these accessories, is that so? Checked that function 2 is set to mode one which is supposed to be correct for this vehicle I have double checked all connections and all are good. Have used a multimeter and both ignition pins with pink and white wire and both are receiving 12 volts when started. Also is there a way to fully takeover the vehicle without shutting it down first or is that just a Honda thing with no workaround? Thanks

2019 Honda Accord Sport Manual Trans - NO START

Thu, 25 Sep 2025 00:36:12 +0000

Hi,

I installed a EVO ONE Kit with RF912 remotes. I tested all connections via multimeter from BCM to Fortin harness. I programmed the remotes, and was able to use DECRYPTER. I am able to get the car in manual ready mode. Parking lights come on and car shuts down upon door closing. Upon calling for remote start, the dashboard lights up, displays "Smart Entry System Problem" (yes I know that is normal for these cars). The parking lights sometimes flash twice other times there is no flash and it just does nothing. The Evo one flashes Blue/Red, then Yellow/Red, the off and repeat for another cycle. No crank.

I have reflashed, disabled A11, no change. I have also attempted to sit in the car holding the clutch down incase the clutch bypass was not working but that did not seem to do anything at all.

Please let me know next steps and what else I should try.