Questions & Answers - Questions récentes

“The Current Device Cannot be flashed anymore”

Fri, 23 Oct 2026 01:06:16 +0000

I have EVO-ALL bypass module. I was trying to flash it and im getting a message "This device cannot be flashed anymore". Serial no: 001A06607172

Please Help!

Evoone with RFK942 remote started, but won't lock or unlock.

Thu, 22 Oct 2026 16:38:33 +0000

2014 Forester installed Evoone with RFK942 remote started, but won't lock or unlock. Factory remote works. Only happened when the remote started. When the car is off everything work.

Highlander

Wed, 21 Oct 2026 18:59:45 +0000

Two months ago, I installed an Evo-ALL module in a 2019 Highlander. The programming process proved difficult—the system only worked on the third attempt. The new module didn't work, so I used an old one instead.

The client called to say that the Fortin device has stopped working.

Is it possible that the vehicle has a factory-installed remote start system that is causing interference? Where should I look for it?

Car starter for a 2013 toyota Matrix - remote compatible

Wed, 21 Oct 2026 11:04:10 +0000

I have a 2013 Toyota Matrix automatic with a Fortin remote starter. The previous owner lost the remote. Can you help me identify the system and find a compatible replacement remote?

Can an EVO-START LTE use a local SIM card to work outside Canada and the USA?

Tue, 20 Oct 2026 04:45:47 +0000

Hello Fortin Support,

I have a working EVO-ONE installation and would like to add smartphone remote-start control. I understand that EVO-START LTE coverage is limited to Canada or the USA, depending on the version purchased.

Is it possible to replace the supplied SIM card with a local mobile-network SIM so that the EVO-START can operate in other countries, specifically South Africa?

Could you please clarify:

- Is the SIM replaceable, and can the device's APN be configured for a local provider?

- Would compatible cellular bands and a local data SIM be sufficient, or do firmware, activation, subscription or Fortin server restrictions prevent it from working outside the supported countries?

- If a SIM swap is not supported, is there an international version or a compatible phone-control module you recommend for use with the EVO-ONE in South Africa?

If the answer differs between EVO-START models, please let me know which models support this, if any.

Thank you for your help.

Client view of fence trigger on phone notification,

Mon, 19 Oct 2026 19:03:05 +0000

Upon phone notification in the phone, we see the notification text showing the

''Enter geofence alarm''

''device:Versa,time:2026-10-19...''

Can the text be more precise on the fence triggered,

Not having the feild description in the text showed, and have the fence showing,

Versa,2026-10-16 08:00,Longueuil fence,....

image

2017 Audi A6 2.0 TDI EVO-ONE: no crank unless brake pressed (guide 79791)

Mon, 19 Oct 2026 13:48:28 +0000

Hello Fortin Support,

I need help verifying the brake activation and CAN1 wiring for an EVO-ONE installed in a 2017 Audi A6 C7.5 2.0 TDI, right-hand drive, automatic, push-to-start.

Installation guide: #79791

Bypass firmware: 60.12

Remote starter firmware: 1.31

DCryptor completed successfully.

Symptoms:

- Pressing lock three times on the OEM remote triggers the ignition, but the engine will not crank unless I physically press the brake pedal.

- The brake lights do not illuminate during the remote-start sequence when the pedal is not pressed.

- If I hold the brake pedal, the engine starts but shuts off after approximately 2 seconds.

Current connections:

- EVO-ONE D2 Yellow/Blue is connected to the vehicle Red/Black brake circuit.

- CAN1 is tapped into the Orange/Green and Orange/Brown twisted pair at the brown 16-pin BCM connector C. The Fortin guide shows a black connector, so I would like to confirm whether my connection point is correct for this RHD C7.5 vehicle.

Could you please verify:

1. The correct brake activation signal for this exact vehicle: connector and pin, wire colour, required polarity/voltage, and whether D2 Yellow/Blue should connect directly to the Red/Black circuit or requires a different interface. Is this the correct signal to satisfy the push-to-start brake requirement?

2. The correct CAN1 High/Low connection point, connector and pin numbers for the RHD C7.5, including whether the brown 16-pin BCM C Orange/Green and Orange/Brown pair is correct despite the black connector shown in guide #79791.

3. The recommended fix and any required firmware or option changes for the no-crank condition and 2-second shutdown.

Thank you.

When I approached the car with my phone, the car unlocks all four doors

Sun, 18 Oct 2026 21:43:37 +0000

When I approached a car with my cell phone, I only want the driver‘s door to unlock not all four doors

2014 Tiguan Firmware per the guide is not found.....

Sun, 18 Oct 2026 18:02:06 +0000

I'm about to install remote start in my 2014 VW Tiguan push start but the guide lists a firmware version of 75.38 but the Flashlink Manager only lists 3 options for fimrware updates for my evo-all, 4.20 Beta, 0.99 Beta, and 0.90 Beta. Which of these three should I install to make sure there are no firmware related issues since none are similar to the firmware version listed in the installation guide (Guide 62501) documentation? Thanks!!!!

reset flashing limits

Sun, 18 Oct 2026 02:29:44 +0000

please reset my flashing limit for evo all module 001A06 283437 AND 001A06 568580

thank you

2015 Nissan Murano programmed new smart key now remote start no working.

Thu, 15 Oct 2026 23:46:02 +0000

2015 Nissan Murano, I lost my smart key (all keys lost) so I had to program two new smart keys now remote start will not work. how do I reset key data. to accept new keys

Could you reset the flash limit for a evo all sn: 001A06756790

Wed, 14 Oct 2026 21:15:01 +0000

Could you reset the flash limit for a evo all sn: 001A06756790

Thank you

Hi I need help resetting decryption on my eve one unit

Mon, 12 Oct 2026 14:32:59 +0000

I own a 2014 Acura Mdx.unfortunately I wasn't aware the unit can be locked after several attempts to decrypt.if you could please rest my unit id much appreciate it.my unit is sn 002B04 753807.thank you

2014 Forester started and shutdown in 3 seconds

Mon, 12 Oct 2026 04:49:11 +0000

2014 Forester started and shutdown in 3 seconds then started and shutdown and started and shutdown 3 times.

Using evoall with avital 5308. Everything programmed correctly. Wires checked. Any suggession? Thank you.

The coolant does not heat up during remote starting.

Sun, 11 Oct 2026 16:21:03 +0000

Hello. I installed an Evo-One on a 2014 Vezel (selecting the 2016 HR-V setting). It was a hybrid vehicle. I selected option D4 in the settings. Do I also need to enable option "26-2" under the "remote start" settings? The client called to say that the engine coolant doesn't heat up during remote start, and when he drives off after remote starting, the blue "cold engine" light remains on. Why do we cut the IGN2 wire?

2009 lexus lx570 takeover?

Sun, 11 Oct 2026 03:29:22 +0000

Hi I have a 2009 lexus lx570 and want to install your system but want to Check if takeover is available? Thanks in advanced

AutoStart is not working for Honda CRV 2015 Touring - Push to Start

Sat, 10 Oct 2026 20:16:06 +0000

I installed a Fortin EVO-ONE with the THAR-HON3 T-harness on a 2015 Honda CR-V Touring Model Push-to-Start .
The module programs correctly, Dcryptor completed successfully, and CAN functions work (lock/unlock, ignition status).
However, the EVO-ONE never outputs ignition during remote start.

Did Enabled option D2

Programmed Remote Started option Function 2 Mode 2

Programmed Remote Started option for R S OEM Remote Stand alone

Function 38 Mode 2

Getting Error while Decrypt Process - Decrpypt Limit has been reached for this Car.

Model - EVO-ONE

Date : 07/2025

SN : 002B04 734872

Appreciate your help to solve the issue please.

Thanks

Is this compatible with audi q5 2022 sportsback Progresiv 45 TFSI quattro ?

Fri, 09 Oct 2026 18:04:24 +0000

Is this compatible with audi q5 2022 sportsback Progresiv 45 TFSI quattro ?

armada starting problem

Wed, 07 Oct 2026 17:06:26 +0000

hello ifix one evo all for nissan armada 2021 sn 001a07 498928

i make the wiring and the decraptor all good when i need to start press lock 3 time the light for device coming blue 3 times after red light coming 5 time with the sound for relay at the harnes for nis1 and the car not starting any help plaese

2024 Prius

Tue, 06 Oct 2026 13:48:12 +0000

Which manual is suitable for the 2024 Prius?

Does it work for base model 01 Chevy Silverado no power windows or locks

Sun, 04 Oct 2026 12:25:49 +0000

Would I be able to use it without electric locks or windows. Just the base model

I'm installing my remote start kit, I'm not seeing any option to go to Pro mode.

Fri, 02 Oct 2026 20:34:05 +0000

Please help

Can you reset flash, pls on my evo all

Thu, 01 Oct 2026 17:16:52 +0000

SERVICE #

001A06288597

Can you make a version of the Flash for Mac OS?

Thu, 01 Oct 2026 16:02:21 +0000

interested In your products, but not looking to buy a New computer.

Please reset flash limit on 5 EVO-ALL modules (service numbers listed)

Thu, 01 Oct 2026 15:50:48 +0000

I spoke with a Fortin rep who said EVO-ALL modules lock after 5 years and can be reset on your end. Please reset the flash limit / lock on these 5 modules so they can be updated and programmed in FlashLink: 1) 001A06 849500 (HW 6, FW 71.34, 09/2018, EVO-FORD/MAZDA) 2) 001A06 835355 (HW 6, FW 71.34, 08/2018, EVO-FORD/MAZDA) 3) 001A06 849469 (HW 6, FW 71.34, 09/2018, EVO-FORD/MAZDA) 4) 001A06 782874 (HW 6, FW 70.16, 12/2017, EVO-GMTx) 5) 001A07 162160 (09/2020, Secure Update). Thank you.

2021 Nissan Frontier - P1612 Immobilzer DTC Code

Wed, 30 Sep 2026 23:28:47 +0000

My EVO-ALL with the NIST4 harness has been great for a few years, but just the other day the vehicle did not start and then set off the alarm due to the failure. My OBD scanner flagged a P1612 DTC CODE related to the ECU & Immobilzer that comes back immediately after clearing. Anyone seen this? I suspect the EVO module somehow lost its key bypass coding, because if I tape up my NISSAN FOB to the key antenna I can get a remote start with my EVO remote since the vehicle has a key active How can the bypass programming get corrupted, and has anyone ever seen this? Strang one.

2018 CRETA

Mon, 28 Sep 2026 12:46:54 +0000

I installed the Evo-One on a 2018 Hyundai Creta (selecting the Kona model). It works well, but where can I find the wire for the "Take Over" function, so the engine doesn't shut off?

Replacement screws for EVO-9 RM912 key ring

Mon, 28 Sep 2026 09:53:39 +0000

The 2 screws holding the key ring on my RM912 are missing. Where can I get some or what are the specs / sizes?

The evo one red, yellow, blue light never stop flashing on my 2011 tacoma

Mon, 28 Sep 2026 05:37:25 +0000

I got The evo one for the remote start but the red, yellow and blue light never stop flashing.

I can’t get The blue and red to stay on all three keep flashing.

I have a 2011 Toyota base Tacoma automatic with G-key

Keep trying step two for hours and can’t get the red and blue light to go on all three lights keep flashing

What can I do to fix this issue

EVO-VWT1 is not flashing RED YELLOW BLUE, Just stays at RED

Sun, 27 Sep 2026 18:32:00 +0000

When I want to program the EVO All module, it just shows solid RED light. Other lights are not flashing.

How can I reset it?

Is LINKR-LT2 compatible with the EVO-ONE?

Sat, 26 Sep 2026 17:57:04 +0000

Hello,

I have an EVO-ALL with a LINKR-LT2 but switching to an EVO-ONE and would like to continue to using the LINKR-LT2. I will be utilizing the TOY16 wiring harness when installing the EVO-ONE. When referencing the EVO-ONE installation guide# 127601 I do not see any mention of the AVEC DATA-LINK connection like it is referenced in the EVO-ALL installation guide# 127591. This is my reasoning for this question.

Thank you.

Do I need to purchase the rlink programming tool to read the key data?

Fri, 25 Sep 2026 15:06:28 +0000

reading the car key data

RX350, LX600

Thu, 24 Sep 2026 17:48:01 +0000

Hello. On the 2024 Lexus LX and RX, the factory alarm does not disarm when using the mechanical key in door. Must unlock the doors using the remite to prevent the factory alarm from triggering. If we install an aftermarket alarm system and unlock the doors using the new system's remote, the factory alarm will go off, right?

EVO-ONE installed want to add Drone X2-LTE how to ?

Mon, 21 Sep 2026 07:20:22 +0000

Hello

I have EVO-ONE installed on my Mazda CX-5 2013 PTS Automatic and want to add Drone X2-LTE, what should i do ? should i use some specific firmware to control my car via drone application ?

Thanks

Ioniq 2021

Sun, 20 Sep 2026 14:03:17 +0000

Hello. The 2021 Ioniq manual states the following... "US Models: If the (~) PATS Data wire is not present, the vehicle is not equipped with an immobilizer. For CAN functions, use programming #2." But where is this "programming #2"?

TB-VW possibly not working? does not remote start-

Sat, 19 Sep 2026 19:00:03 +0000

please help!

2016 jetta with auto transmission and mechanical Key. Using guide 65601 and THAR-VW3, TB-VW.

when attempting to remote start. red light is solid, then red and yellow lights come on solid during sequence, ignition on but no crank. then 3 flash Red. quick support here says likely TB-VW no communication but I did not even need to wire much as it was T-harness included so is it the TB that was just sent to me defective? only wire I cut was at the ignition (there is white and black) but as per instructions either should be fine. Programing went fine, as well as D cryptor. However, on step 13 (to be very specific) says the Red and yellow should stay off. for what is worth, all lights were off.

one last thing if it matters, I am installing it with a EV0-START-LTE. but has not been activated ( I assume it does not matter as I am first testing 3 lock) this EVO start, also gives it some sort of an extra connection guess but I feel confident all should be fine.

Any help would be super appreciated!

Can you reset my modul or i need to send it back?

Sat, 19 Sep 2026 18:27:08 +0000

I've bought a Fortin evo-all with thar-audi1 for my 2010 a4. I've tried to flash but received a msg "the current device cannot be flashed anymore". No key required system. SN 001A06853395, preload date 40/2018, hardware 6.0, firmware 4.18, flash limit 0/0. What should i do?

Reset request for EVO-ALL that says "The current device cannot be flashed anymore"

Sat, 19 Sep 2026 02:13:05 +0000

I bought a used EVO-ALL, but it is unable to be flashed. Can you please reset it?

Service # 001A06 550326

Hardware Vr. 6

Firmware Vr 4.16

Date 09/2015

Type - 2

Thank you for your time!

FLASH LIMIT REACHED

Fri, 18 Sep 2026 17:53:20 +0000

FLASH LINK DCRYPTOR MAXED OUT

SN: 002B04738001

CAN YOU REST PLEASE?

Bought unit in scrap yard - Evo-one

Wed, 16 Sep 2026 17:07:18 +0000

Hi, I have bought an evo-all and evo-start antenna in a scrap yard. Is there anyway to factory reset the unit to be used again on a new vehicle? (both evo-all and antenna)

Compatibility confirmation Fortin EVO-ONE-441 – Mazda CX-5 2017

Wed, 16 Sep 2026 11:03:57 +0000

Hello,
I have a 2017 Mazda CX-5 2.5 Grand Touring, USA specification, Push-to-Start, automatic transmission.
VIN: JM3KFBDLXH0170683

I would like to install Fortin EVO-ONE-441 with the appropriate Mazda T-harness.
Please confirm that this setup is fully compatible with my vehicle and tell me exactly which T-harness and firmware/installation guide are required.
I would also like the system to work with the included remote controls.

Thank you.

Fortin FSS Dual Stage Shock Sensor

Sun, 13 Sep 2026 22:52:11 +0000

I have a Fortin EVO-ALL THAR-AUD1 remote start installed in mt 2012 Audi S4, and would like to know if I can install a FSS Dual Shock Sensor to this unit.

2009 Honda Civic not entering Ready Mode

Sun, 13 Sep 2026 18:49:03 +0000

Hello,

My 2009 Honda Civic Manual Transmission is not entering Ready mode. I have an Evo One with T-harness thar1 installed. I had this installed previously in my last Civic of same model and year. I did reset the module and update the firmware since I hadn't programmed it in a few years. With the car running, I apply and hold the foot brake, apply the hand brake, then release the foot brake. It should flash the cars lights and enter Ready Mode at this point, but does not. I am wondering if it is the firmware update or an option I changed by mistake causing the issue.

Bypass Options:

Firmware: 73.[41]
Hardare: 4.0

A1 Door Locks
A3 Key Bypass
A7 Foot Brake (Output Status)
A8 Hand Brake (Output Status)
A9 Door Trigger (Output Status)
A10 Trunk Trigger (Output Status)
B1 Unlock Driver Door Only
C1 OEM Remote Monitoring
D2 Unlock Before/Lock After (Disarm OEM Alarm)
D4 Hybrid Mode
D5 Lock After Start

Remote Starter:
2.1 Programmable Output (+) IGN/ACC/START
3 Tachless Sensitivity 1
4.1 Remote Car Starter Runtime 15 MIN
6.1 Door Lock Before And After Remote-Start NO
7.1 Ignition Door Lock NONE
8.1 Unlock Pulse Time SINGLE 0.25
9.1 Active or Passive Starter Kill ACTIVE
10.1 Starter Kill Output
11.1 Confirmation Sound and Antenna LED
12.1 Output Horn/Siren
13.2 Confirmation Pulse SHORT
14.1 Alarm On/Off Starter On/Off
15.1 Smart Door Lock
16.5 Cold Start Timer OFF
18.1 Diesel Mode DISABLE
19.1 Turbo Mode DISABLE
20.6 Engine Supervision
21.1 Start Attempts 2 Times
24.1 Special Applications DISABLE
25.1 Yellow/Black (A13):Aux1
26.1 Hybrid Mode GAS / Diesel Vehicle
29.1 Alarm Duration 30 Sec
30.1 Valet Code
31.1 Special Application Programmable Output (+) DISABLE
32.1 Ground Output
33.2 Manual Transmission Ready Mode Activation Hand & Foot Brake ON
35.1 Door Unlock Special Application DISABLE
36.2 Activation/Deactivation Remote Valet Mode
37.1 Security Remote Car Starter Special Application DISABLE
38.2 System Control by OEM Remote 3x LOCK
39.1 Temperature Option DISABLE

Thank You.

EVO-ALL Red and yellow balloon flashes

Sat, 12 Sep 2026 17:32:26 +0000

I have a problem related to programming on a 2023 Audi car, and at the beginning there was no problem, when I checked an update, and when I sent it to the vehicle, it did not work remotely, otherwise it appeared to me in red and yellow colors in a device, and when I searched for it, it said that it is not possible to connect, and until the factory has been reset, and also on its programming, it shows me the colors red and yellow, and when I connected the device to a computer, he said it is not possible to see.I have a problem related to programming on a 2023 Audi car, and at the beginning there was no problem, when I checked an update and when I sent it to the vehicle, it did not work remotely, otherwise it appeared to me in red and yellow colors in a device, and when I searched for it, it was not possible to connect, and until the factory was reset and also on its programming, the colors red and yellow appear to me, and when I connected the device to a computer, he said it could not take the programming and follow.I have a problem related to programming on a 2023 Audi car and it was initially no problem when I check for an update and when I sent it to the vehicle it does not work remotely otherwise it appears to me in red and yellow colors in a device and when I look for it that it is not possible to connect and until the factory has been reset and also on its programming it shows me the two colors red and yellow and when I connected the device to the computer he said it cannot take the programming and follow the number 1 of the steps and when I follow the steps the same problem returns in the red and yellow colors I think it needs to reset the factory through youI have a problem related to programming on a 2023 Audi car, and at the beginning there was no problem, when I checked an update, and when I sent it to the vehicle, it did not work remotely, otherwise it appeared to me in red and yellow colors in a device, and when I searched for it, it was not possible to connect, and until the factory was reset and also on its programming, it shows me the colors red and yellow, and when I connected the device to a computer, he said it could not take the programming, and I followed the number 1 of the steps, and when I follow the steps, the same problem returns in the colors red and yellow, I think it needs to be reset the factory throughI have a problem related to programming on a 2023 Audi car and it was initially no problem when I check for an update and when I sent it to the vehicle it does not work remotely otherwise it appears to me in red and yellow colors in a device and when I look for it that it is not possible to connect and until the factory has been reset and also on its programming it shows me the two colors red and yellow and when I connected the device to the computer he said it cannot take the programming and follow the number 1 of the steps and when I follow the steps the same problem returns in the red and yellow colors I think it needs to reset the factory through you
SN: 001A07 595395

2019 Jeep Cherokee EVO-ALL won’t start

Fri, 11 Sep 2026 18:59:57 +0000

I need help. I've been a couple days now with this. EVO-ALL installed programming goes fine, but it will not tun over the car. Module comes to life on 3x lock, cycles the gauges, but then just stops and tries again.

Blue light is not blinking at steps 8 & 9

Fri, 11 Sep 2026 18:55:11 +0000

I got the Fortin EVO-CHRT7 All in One Remote Start & Interface Kit w/T-Harness + Flash-Link Updater Bundle - Plug & Play Solution for Select 2013 Chrysler/Dodge/Jeep Vehicles. The Flash updater shows upto chrt6 not chrt7 for flashing the evo all module when adding in vehicle details for 2013 Dodge Dart 2.0 L Automatic transmission standard key. The followed the guide #98631, the module doesn't flash at step 8 its stays solid. I have attached the ignition and parking wire. I have attached the pictures for them. Is connecting the hood pin essential for programming?

2019 Jeep Cherokee PTS not starting on EVO-CHRT7

Fri, 11 Sep 2026 15:44:19 +0000

Please reset decryption limit

Thu, 10 Sep 2026 18:17:48 +0000

Can I get the decryption limit reset on EVO-ALL SN 001A07 734548? Having issues with an install.

RX450h Take Over

Thu, 10 Sep 2026 08:07:38 +0000

How to implement "Take Over" in the RX450h using the Evo-All (with remote start device)?

Key Bypass Programming stuck at Step 5 on 2009 Honda Civic Evo-One w/ T-Harness

Mon, 07 Sep 2026 23:26:46 +0000

Hello,

I get stuck at Step 5 when trying to program key bypass.

1) Press and hole programming button while connection 6-pin main connector.

2) Released the programming button when the led is Red

3) Inserted the remaining connectors (A-20-pin,D-Red,C-White,B-Blue)

4) Pressed and released programming button twice (x2). Red led flashes once per second.

5) Turned key to On/Run position. Leds turned off. (Should have flashed red 10 times then blue flashing.) This is where I get stuck every time. I did notice that if I remove the 20-pin at this point, then the leds flash properly (Red x10. Blue rapidly) I replace the 20-pin and try to prepare remote start but nothing happens.

Thank you.