Questions & Answers - Recent questions tagged evo-all

Highlander

Wed, 21 Oct 2026 18:59:45 +0000

Two months ago, I installed an Evo-ALL module in a 2019 Highlander. The programming process proved difficult—the system only worked on the third attempt. The new module didn't work, so I used an old one instead.

The client called to say that the Fortin device has stopped working.

Is it possible that the vehicle has a factory-installed remote start system that is causing interference? Where should I look for it?

2014 Tiguan Firmware per the guide is not found.....

Sun, 18 Oct 2026 18:02:06 +0000

I'm about to install remote start in my 2014 VW Tiguan push start but the guide lists a firmware version of 75.38 but the Flashlink Manager only lists 3 options for fimrware updates for my evo-all, 4.20 Beta, 0.99 Beta, and 0.90 Beta. Which of these three should I install to make sure there are no firmware related issues since none are similar to the firmware version listed in the installation guide (Guide 62501) documentation? Thanks!!!!

Can you reset flash, pls on my evo all

Thu, 01 Oct 2026 17:16:52 +0000

SERVICE #

001A06288597

Please reset flash limit on 5 EVO-ALL modules (service numbers listed)

Thu, 01 Oct 2026 15:50:48 +0000

I spoke with a Fortin rep who said EVO-ALL modules lock after 5 years and can be reset on your end. Please reset the flash limit / lock on these 5 modules so they can be updated and programmed in FlashLink: 1) 001A06 849500 (HW 6, FW 71.34, 09/2018, EVO-FORD/MAZDA) 2) 001A06 835355 (HW 6, FW 71.34, 08/2018, EVO-FORD/MAZDA) 3) 001A06 849469 (HW 6, FW 71.34, 09/2018, EVO-FORD/MAZDA) 4) 001A06 782874 (HW 6, FW 70.16, 12/2017, EVO-GMTx) 5) 001A07 162160 (09/2020, Secure Update). Thank you.

Is LINKR-LT2 compatible with the EVO-ONE?

Sat, 26 Sep 2026 17:57:04 +0000

Hello,

I have an EVO-ALL with a LINKR-LT2 but switching to an EVO-ONE and would like to continue to using the LINKR-LT2. I will be utilizing the TOY16 wiring harness when installing the EVO-ONE. When referencing the EVO-ONE installation guide# 127601 I do not see any mention of the AVEC DATA-LINK connection like it is referenced in the EVO-ALL installation guide# 127591. This is my reasoning for this question.

Thank you.

TB-VW possibly not working? does not remote start-

Sat, 19 Sep 2026 19:00:03 +0000

please help!

2016 jetta with auto transmission and mechanical Key. Using guide 65601 and THAR-VW3, TB-VW.

when attempting to remote start. red light is solid, then red and yellow lights come on solid during sequence, ignition on but no crank. then 3 flash Red. quick support here says likely TB-VW no communication but I did not even need to wire much as it was T-harness included so is it the TB that was just sent to me defective? only wire I cut was at the ignition (there is white and black) but as per instructions either should be fine. Programing went fine, as well as D cryptor. However, on step 13 (to be very specific) says the Red and yellow should stay off. for what is worth, all lights were off.

one last thing if it matters, I am installing it with a EV0-START-LTE. but has not been activated ( I assume it does not matter as I am first testing 3 lock) this EVO start, also gives it some sort of an extra connection guess but I feel confident all should be fine.

Any help would be super appreciated!

Can you reset my modul or i need to send it back?

Sat, 19 Sep 2026 18:27:08 +0000

I've bought a Fortin evo-all with thar-audi1 for my 2010 a4. I've tried to flash but received a msg "the current device cannot be flashed anymore". No key required system. SN 001A06853395, preload date 40/2018, hardware 6.0, firmware 4.18, flash limit 0/0. What should i do?

Reset request for EVO-ALL that says "The current device cannot be flashed anymore"

Sat, 19 Sep 2026 02:13:05 +0000

I bought a used EVO-ALL, but it is unable to be flashed. Can you please reset it?

Service # 001A06 550326

Hardware Vr. 6

Firmware Vr 4.16

Date 09/2015

Type - 2

Thank you for your time!

Bought unit in scrap yard - Evo-one

Wed, 16 Sep 2026 17:07:18 +0000

Hi, I have bought an evo-all and evo-start antenna in a scrap yard. Is there anyway to factory reset the unit to be used again on a new vehicle? (both evo-all and antenna)

EVO-ALL Red and yellow balloon flashes

Sat, 12 Sep 2026 17:32:26 +0000

I have a problem related to programming on a 2023 Audi car, and at the beginning there was no problem, when I checked an update, and when I sent it to the vehicle, it did not work remotely, otherwise it appeared to me in red and yellow colors in a device, and when I searched for it, it said that it is not possible to connect, and until the factory has been reset, and also on its programming, it shows me the colors red and yellow, and when I connected the device to a computer, he said it is not possible to see.I have a problem related to programming on a 2023 Audi car, and at the beginning there was no problem, when I checked an update and when I sent it to the vehicle, it did not work remotely, otherwise it appeared to me in red and yellow colors in a device, and when I searched for it, it was not possible to connect, and until the factory was reset and also on its programming, the colors red and yellow appear to me, and when I connected the device to a computer, he said it could not take the programming and follow.I have a problem related to programming on a 2023 Audi car and it was initially no problem when I check for an update and when I sent it to the vehicle it does not work remotely otherwise it appears to me in red and yellow colors in a device and when I look for it that it is not possible to connect and until the factory has been reset and also on its programming it shows me the two colors red and yellow and when I connected the device to the computer he said it cannot take the programming and follow the number 1 of the steps and when I follow the steps the same problem returns in the red and yellow colors I think it needs to reset the factory through youI have a problem related to programming on a 2023 Audi car, and at the beginning there was no problem, when I checked an update, and when I sent it to the vehicle, it did not work remotely, otherwise it appeared to me in red and yellow colors in a device, and when I searched for it, it was not possible to connect, and until the factory was reset and also on its programming, it shows me the colors red and yellow, and when I connected the device to a computer, he said it could not take the programming, and I followed the number 1 of the steps, and when I follow the steps, the same problem returns in the colors red and yellow, I think it needs to be reset the factory throughI have a problem related to programming on a 2023 Audi car and it was initially no problem when I check for an update and when I sent it to the vehicle it does not work remotely otherwise it appears to me in red and yellow colors in a device and when I look for it that it is not possible to connect and until the factory has been reset and also on its programming it shows me the two colors red and yellow and when I connected the device to the computer he said it cannot take the programming and follow the number 1 of the steps and when I follow the steps the same problem returns in the red and yellow colors I think it needs to reset the factory through you
SN: 001A07 595395

Blue light is not blinking at steps 8 & 9

Fri, 11 Sep 2026 18:55:11 +0000

I got the Fortin EVO-CHRT7 All in One Remote Start & Interface Kit w/T-Harness + Flash-Link Updater Bundle - Plug & Play Solution for Select 2013 Chrysler/Dodge/Jeep Vehicles. The Flash updater shows upto chrt6 not chrt7 for flashing the evo all module when adding in vehicle details for 2013 Dodge Dart 2.0 L Automatic transmission standard key. The followed the guide #98631, the module doesn't flash at step 8 its stays solid. I have attached the ignition and parking wire. I have attached the pictures for them. Is connecting the hood pin essential for programming?

Evo-all installed on a 04 Hummer H2. On the 20 pin connector. What color wire is connected to a constant 12v?

Thu, 13 Aug 2026 19:05:20 +0000

04 Hummer H2, installing a pke with push start button and the evo all. While trying to program the evo box. I follow the instructions to push the button on the evo while connecting the 4 pin connector. I wait till led blue light is lit. Release the button. Connect the 20 pin connector to the evo. Turn the Hummer key to the on position. According to the ins traction, the blue led light is supposed to start flashing. There is my problem. I was told to make sure the 20 pin connector black wire is grounded to chassis and the red/blue wire is connected to constant 12v. I need to verify the constant 12v connection, before I connected and burn the evo box.

EVO-ONE or EVO-ALL + INT-LRV on a 2008 European Freelander 2 (LR2) diesel — supported, which module for RF kit?

Mon, 10 Aug 2026 19:09:33 +0000

Vehicle: Land Rover Freelander 2 (sold as LR2 in North America), 2008, 2.2 TD4 diesel, automatic transmission, HSE trim, European market (France), motorized keyport with Engine Start/Stop button. VIN: SALFA24B08H113452

I have read the vehicle page for LR2 2008 Standard-Key, the INT-LRV install guide Rev.G (2012-04-13), and the EVO-ALL Volvo/Land Rover addendum #3322 (rev. 20120430), where Freelander-LR2 2006-2010 is listed as Connection 2 / Program 1. I also read the Jaguar X-Type 2008 EU diesel answer and the F150 standalone answer, so I understand my VIN may not pull up in your NA database and that EVO-ALL standalone only works via data or low-current start. My questions:

The INT-LRV guide lists the vehicle under its European name "Freelander-LR2", so I'm hoping European-market vehicles were part of the validation. Has any European/UK Freelander 2 diesel install been reported? If it's "at your own risk", I accept that — but what would the failure mode be if the CAN data differs on the EU diesel: no status data only, or no remote start at all?
On this push-to-start vehicle, is EVO-ALL + RFK442 standalone supported, or do I need the EVO-ONE to provide the ignition output shown in the INT-LRV diagram? Is a diesel glow-plug delay supported?
INT-LRV: can you confirm the factory keyport stays fully functional for daily use after installation, and that the module can later be removed (service jumper) by re-soldering the two original wires, with no permanent modification to the vehicle?
Is there a newer revision of the INT-LRV guide than Rev.G 2012, or any known notes specific to the Freelander 2? Which install guide number and firmware should I use?
Can the module be purchased pre-flashed, and do you ship to France (EVO module + INT-LRV + RF kit + FlashLink Updater), or is there a European distributor?

For context: I have the Land Rover SDD diagnostic tool and can program my own key fobs (I plan to use a self-programmed spare fob as the sacrificed remote), and I have a precision soldering station.

Processing update never updates

Tue, 04 Aug 2026 02:38:46 +0000

I'm on the last step but I can't get past the decryptor and I've been at this all day.

2013 A8 remote start

Thu, 30 Jul 2026 10:24:20 +0000

Hello. I installed Evo-All on 2013 A8.(The car owner brought the Evo-ALL module himself). It only worked with the old firmware version 60.{10}... It started with three presses on the OEM remote, but it wouldn't turn off. Then I connected the white/black wire instead of the light/blue wire, and everything was fixed. Is there a mistake in the instructions, or what?

Why is the vehicle not responding?

Sat, 18 Jul 2026 14:20:58 +0000

I have a Fortin evo all, a evo start lte, and also shock sensor. I’m getting feedback from the car which shows up on the Evo start, but commands sent aren’t working, and when the evo alarm goes off the vehicle alarm does not. I was hoping you could tell me if there’s some wiring that I’m not aware of, or if the process with the dcryptor is wrong? everything seemed to program correctly. I used the CHR7 T-harness and it’s on a 2018 grand Cherokee. What am I missing?

Hello my module is at a limit and needs to be reset SN: 001A07793670

Tue, 07 Jul 2026 21:59:22 +0000

SN: 001A07793670

2017 Renegade

Fri, 12 Jun 2026 21:22:01 +0000

Hello. When I'm programming the Evo-All on a 2017 Jeep Renegade, the blue LED starts blinking after 5 seconds (after pressing the button), and after turning off the ignition, the red LED stays on continuously. I've already tried it on two modules.

EVO-ALL cannot program sacrificied key in a standlone installation for Tiguan 2020 PTS

Thu, 11 Jun 2026 15:08:31 +0000

I am trying to setup a standalone installation for Volkswagen Tiguan 2020 European Trim with PTS and with digital cluster
I have wrapped the sacrificied key (even tried an oem ring) and connected the wiring following the guide # 94761

The ignition is not turning ON during programming (seems that Evo-All is not getting the key data from pin D5 and hence not sending it via pin D4 to the vehicle)
Hence when i press ingition ON during progamming the car tells me to get the key inside the vehicle

Evo-All SN: 001A07 026604
Date: 05/2019
Evo-All FW: 61.35

Sacrificed Key
Sacrificed Key_2
OEM Transponder Antenna Connection
OEM Transponder Antenna Socket Front View

2017 IS-300

Mon, 25 May 2026 14:08:46 +0000

Hello. I installed a remote starter on a 2017 IS-300. I reprogrammed the firmware three times, but it didn't help. It programmed successfully, but when I pressed the button on the factory remote, the blue LED didn't respond (001A07213969). After that, I installed a different module, and it worked. What could be the cause?

Please Reset and Guide Me, my EVO‑ALL Cannot Decode the Key

Thu, 21 May 2026 22:55:16 +0000

flash link mod sn: 002505 113604

Evo all sn: 001A07 414563

my car is Mazda cx5 2021+ signature turbo

my key fob is the larger version, not the small one shown in the instructions, so I got stuck at the key‑learning step. I tried many times—turning the ignition on and off repeatedly, rotating the key in every direction—but the EVO‑ALL still couldn’t learn the key and stayed on the blue LED the whole time.

I then switched to the blue‑LED programming method (the one that doesn’t require manual key learning) from YouTube videos, but when I pressed lock–unlock–lock, the EVO‑ALL received the signal but the car still wouldn’t start. It ended with 3 red flashes, probably because it couldn’t decode the key.

After that, I reflashed the firmware and programmed it again, but it still didn’t work. The software even locked the decryption function for my vehicle. Please help me.

I've just double check and saw that 32pin (not in THAR-MAZ1) but Are the “DOOR LOCK DATA” and “DATA KEY” wires on the THAR‑MAZ1 required to be connected? <-- I've already connected them, but still Stop at blue led. >.<

proplem in module

Sun, 17 May 2026 14:16:42 +0000

hello dear sorry for disturbing you

I have a problem with a device

Model: EVo-ALL

DATE:10/2025

Fortin CA

SN: 001A07789405

I tried to install the device multiple times on my personal vehicles, which is a 2017 Chevrolet Silverado truck that uses a key for ignition. When I tried to install the module, the yellow light stopped, and when I tried to update the module, the following message appeared (invalid Key data). Is it possible for me to re-download the program from you, for your information my firmware 70XX

Can you please reset my Evo-all module SN: 001A07458358

Tue, 12 May 2026 19:14:16 +0000

Unfortunately it reached the maximum flash when I tried to fix error what happened when I installing the device

So If you Can you please reset my Evo-all module SN: 001A07 458358 i well be grateful to you

Does your can bus interface work with a 2005 Pontiac gto

Thu, 07 May 2026 03:04:59 +0000

Can ANY of your devices (immobilizers) work on a 2005 Pontiac gto?

Dcryptor Limit Has Been Reached

Tue, 14 Apr 2026 04:09:38 +0000

Please, I need to reset this module limit EVO-ALL

S/N : 001A07 695901

can you please reset my device ? SN:001A08 006593

Mon, 13 Apr 2026 23:05:09 +0000

fortin Evo-All

SN: 001A08 006593

Infiniti qx70 limited 2017

Thu, 09 Apr 2026 19:18:34 +0000

Hello.After programming, the red and orange LEDs flash. I don't know what's going on. Please help.T wiring harness.

Hello just bought a new vehicle and i need my EVO-ALL reset. 001A07 059211

Wed, 08 Apr 2026 22:39:49 +0000

Hello just bought a new vehicle and i need my EVO-ALL reset. 001A07 059211

What’s the range of the phone application

Fri, 27 Mar 2026 10:56:54 +0000

If i install the EVO application i want to know what’s the range that i can start my Prado from the phone app? I work in an office tower on the 23 floor and my car is parked on the ground floor so i wanted to know if it will detect this range

DCRYPTOR LIMIT HAS BEEN REACHED

Fri, 20 Mar 2026 22:41:11 +0000

Hello dear,

I need to reset this module limit EVO-ALL

S/N : 001A07 535399

Firmware for 2010 Rav4

Tue, 17 Mar 2026 00:21:45 +0000

Can you help me flash older firmware on my Evo-All? For example, from 79/56 to 79/65 ? S/N 001A08005655

Dcryptor limit reached for this vehicle. Reset help?

Sat, 14 Mar 2026 19:17:54 +0000

I have an EVO-ALL and I am trying to setup my CarLINK ASCL7 on my 2019 Toyota Camry PTS to work with it and I've had to change some settings and swapping around the wiring harness. That still doesn't work but the Dcryptor limit has been reached for this vehicle. I need help resetting it.

Service # 001A07 662583

Also if anyone knows the correct flash manager settings and wiring harness setup that would be extremely helpful.

VW Tiguan 2012 EVO-ALL

Sun, 08 Mar 2026 20:47:56 +0000

EVO-ALL , I install Fortin FlashLink Manager, The Flashlink adapter failed to connect to module, I press button "retry detection" red light illuminate on module, after couple seconds i see again to "retry detection", what can be a connection problem?

Can I use EVO-ALL with Viper Remote Start and Keyless Entry?

Tue, 17 Feb 2026 04:25:53 +0000

My mother has a 2013 Ford F150 and I am going to put a remote start in it. I have one already that I am planning to use. It is a Viper 4103XV. I obviously need an immobilizer bypass module as well. I am just trying to find out if the EVO-ALL would work in this setup. I have an opportunity to purchase one from a friend for a good price. Thanks for your help!

Remote only work if I push switch to "ON" on my 2020 Toyota Highlander

Tue, 17 Feb 2026 02:05:08 +0000

Remote only work if I push switch to "ON" on my 2020 Toyota Highlander (non hybrid). please help.

I have evo all rf442

2024 CHR

Tue, 10 Feb 2026 18:18:11 +0000

I installed a 3xlock remote engine start on a 2024 CHR. Everything was the same as on a 2024 Prius Prime...only some of the wire colors were different.

EVO-ALL RF64 -2 Remote, antana LED wont go on? WHY?

Mon, 09 Feb 2026 05:25:20 +0000

Hi again! 2019 Toyota Highlander Push-start.

So Ive been able to go through GUIDE # 70751, and everything works great. The Blue LED is on, flashes, and turns off. I go to page 7 because the remotes I have are the RF64-2W ( is this what I am supposed to do?), but step 3, when it says that the "antenna LEDs should turn on, then blink as you press the brake, turning all three LEDs on the module on." This does not occur; the module stays Yellow and the antenna doesn't turn on once the ignition is on 2X press.

What am I doing wrong? Do I go straight to the remote GUIDE # 33021? When the car is on, the remote works. Is there a step-by-step video or something? I feel like I am just missing one part.

Need help q50 not starting

Sun, 08 Feb 2026 08:13:09 +0000

I have Infiniti q50 2016 3.0L

I installed the EVO-NIST4 to use with OEM key fob , the ignition is tuning on but no cranking, then the red LED flashes 3 times,

the SN is 001A07471366

here is the sequences of LEDs during the attempt

OEM key fob locks 3 times

red LED

red and yellow LED

Then yellow LED is on

vehicle hazards indicator flashed 7 time

After that the red LED flashed 3 time

I checked all the connectors

The car locks and unlocks when the blue LED flashes

I didn’t connect the hood pin

I reprogramed the module

followed the recommended option by the software but I’m not sure the options I’m selecting are correct for my setup

I’m following guide 75841

Reset the flash count

Fri, 06 Feb 2026 18:27:46 +0000

Hi there, could you please reset my flash count had some issues and I had to refresh it

SN: 001A07 225308

thank you

How can I get my Evo all reprogrammed?

Thu, 05 Feb 2026 00:58:20 +0000

Purchased a used toyota highlander that has the Evo- all installed. It Worked for one day then stopped working, I think I accidentally erased the module trying to reprogram it. Any help with what I need to do. Would be great!

Info on the module : MODEL. EVO-ALL DATE

11/2022

FORTIN CA

SN: 001A07 449681

Firmware 79.65 type Toyota

No start Q50 2016 EVO-NIST4

Wed, 04 Feb 2026 08:38:27 +0000

Hi,

I have Infiniti q50 2016 3.0L

I installed the EVO-NIST4 to use with OEM key fob , the ignition is tuning on but no cranking, then the red LED flashes 3 times,

the SN is 001A07471366

here is the sequences of LEDs during the attempt

OEM key fob locks 3 times

red

red and yellow

yellow

vehicle hazards indicator flashed 7 time

red flashed 3 time

I checked all the connectors

The car locks and unlocks when the blue LED flashes

I didn’t connect the hood pin

reprogramed the module

followed the recommended option by the software but I’m not sure the options I’m selecting are correct for my setup

I’m following guide 75841

Any help would be appreciated

Subaru Impreza, computar and Evo all

Tue, 03 Feb 2026 04:18:09 +0000

Hello, I have a 2016 Subaru Impreza with a Compustar alarm and an Evo-All module. Everything works fine while the vehicle is off. lock, unlock, trunk, etc. But when I use the remote start, the vehicle unlocks the doors to disarm the alarm and starts normally, then the lights flash as if it's locking again, but it doesn't. If I press the lock button on the Compustar remote, the vehicle's lights flash as if it's locking, but nothing happens. However, if I use the original remote, it locks properly. It seems that the Evo-All module isn't responding when the car is running. I've been having this problem lately with Subarus when using a Compustar remote start and an Evo-All module. What can I do? Thanks.

Evo all Sn: 001A07732407 05/2025

"DCRYPTOR'S LIMIT HAS BEEN REACHED

Mon, 02 Feb 2026 02:23:10 +0000

I need help resetting the evo all for a 2016 jeep cherokee mpc remote stater. I had trouble programming it to my jeep and reached maxed attempts

Eva-All modules with PTS

Fri, 30 Jan 2026 18:00:13 +0000

Hello friends,

We are a newly forming company developing products for vehicle access and start/stop integrations.

We are working on using EVO-ALL on Push-To-Start (PTS) vehicles to execute Start/Stop and Lock/Unlock functions via a hardwired external trigger (MCU/digital input).

Our first test vehicle is a 2020 Honda CR-V (PTS). For this vehicle, we are considering the EVO-ALL module.

1) Does the EVO-ALL support engine START/STOP control via an “external trigger / hardwired input”?

(Either as a toggle input or as separate START and STOP inputs.)

Additionally, when we perform an engine start through the module, the immobilizer bypass must be handled automatically.

2) In the same way, is it possible to trigger door LOCK/UNLOCK and TRUNK OPEN functions via “external inputs” (hardwired MCU control) using EVO-ALL?

3) For this vehicle, is the required hardware EVO-ALL + THAR/T-Harness + FlashLink/programming tool?

Could you please share the exact product part numbers?

Also, for vehicles without PTS hardware (basic mechanical ignition with immobilizer), do you offer any modules to add an external Engine Start/Stop button?

Ideally, we are looking for solutions that can be implemented via relays.

After successful field tests, we plan to expand to other vehicles (PTS and non-PTS) such as Hyundai/Fiat/Mercedes, and then proceed with volume purchases.

Thank you,

Fehmi ŞAHİN

Turkey

le tiguan 2018 ne demarre pas, la cle valet entourée de fils ne semble pas fonctionner

Sun, 25 Jan 2026 22:42:37 +0000

Quand on actionne le demarreur, on peut voir sur le tableau de bord qu'il ne voit pas de clé. il essaie 2 fois et barre les portes. les lumieres du vehicule flash 1 fois. J'ai 10 tours de fils autours de la cle valet.

Merci de m'aider

EVO-AUDT2 in 2022 Q7 wont program key or recognize key fobs when T-Harness installed

Wed, 21 Jan 2026 21:11:12 +0000

Issue:
Vehicle does not detect key fobs when THAR-AUD2 T-harness is installed

Hardware:

EVO-ALL
THAR-AUD2 T-harness (from EVO-AUDT2 kit)

Symptoms:
When the THAR-AUD2 T-harness is installed, the vehicle displays the message:

“Remote Control Key. Hold back of key against designated area.”

The vehicle will not start.

Troubleshooting Performed:

Placed working fob (with battery) in the cup holder (designated area) → vehicle still does not start
Second fob is attached to the harness antenna with the battery removed
Attempted EVO-ALL programming procedure (waited for LED to turn blue) → no change
Tried starting with working fob in hand and in cup holder → same message
Disconnected EVO-ALL module from the T-harness → issue still occurs
Removed the T-harness completely → vehicle immediately detects both fobs and starts normally
Reinstalled T-harness → issue returns

Key Observation:
The issue occurs solely from installing the THAR-AUD2 T-harness, even with the EVO-ALL module disconnected. Removing the harness restores normal key detection and vehicle operation.

Request:
Please advise if this is a known issue with the THAR-AUD2, a compatibility concern, or if additional configuration or wiring checks are recommended.

2011 Toyota RAV4 Push Start – Remote Start shuts off first time, runs fine second time

Mon, 12 Jan 2026 11:13:29 +0000

Hi everyone,

I installed a remote starter on a 2011 Toyota RAV4 push start using a Compustar 930S with CM900 brain and Fortin EVO-ALL bypass module.

On the first remote start attempt, the vehicle starts normally, then shuts off after about 5–6 seconds. Immediately after shutting down, the system automatically attempts to start the vehicle again without me pressing the remote, and on this second attempt it stays running normally.

Installation and programming were completed as instructed. No fault lights, and the EVO-ALL appears to be learned properly.

Has anyone seen this behavior before on Toyota push-to-start vehicles?

2020 jeep renegade remote start

Mon, 12 Jan 2026 08:36:40 +0000

For information. I installed Evo-ALL on a 2020 Jeep Renegade. I specified the Jeep Compass in the manager. It only took CAN-1...I took CAN from the lower connector behind the BCM. From the thin green and brown wires. I took the parking light line back to the place where it was indicated on the previous model. Programming required opening the ON switch 10 times, as written in the manual. The PTS line was blue. The data line was yellow-blue.

Evo all reading cannot be fshed anymore

Sun, 04 Jan 2026 01:09:06 +0000

Need my Dcryptor reset s/n 001A07-756892 . Its reading device cannot be flashed anymore

This is not a question, it's a bug report.

Sun, 04 Jan 2026 00:38:10 +0000

I installed Evo-All + RF411 on INFINITY QX50.

1. Wire color on OBD connector is different : pin 16 +12v - its YELLOW, pin 8 Ign - its White. Unfortunately, I didn't take a photo.

2. After installation, I programmed the bypass and everything worked. LOCK-LOCK-LOCK - and car start.

But after I programmed the RF411 remotes, the car wouldn't start either with the RF411 remote or with the OEM LOCK_LOCK_LOCK remote. There was a transmission error that it was not in park. I reprogrammed the bypass and everything worked.